Moto XT1643 (Moto G4 Plus) FRP DONE

[Prince]

Moto XT1643 (Moto G4 Plus) FRP DONE


[img=346x435]http://n-android.com/wp-content/uploads/2017/11/motorola_moto_g4_plus.jpg[/img]

Moto XT1643 Moto G4 Plus FRP remove method SigmaKey
How to Bypass FRP in Moto XT1643 Moto G4 Plus with Sigmakey. Moto XT1643 Moto G4 Plus FRP Byapss Remove.

Sigma Pack 2 should be activated.
Here are the Logs:

SigmaKey v.2.26.16
********* Sigma dongle 2.26, Initializing…OK
Pack 1: Activated
Pack 2: Activated
Pack 3: Activated
——— 2017-11-28 15:54:46 ———
SigmaKey 2.26.16 Qcom: [color=#1b8ede]Connect[/color] Motorola Android phone
Connecting…Done
——— 2017-11-28 15:56:36 ———
SigmaKey 2.26.16 ADB: Connect Motorola Android phone
[color=#1b8ede]Firmware[/color]: MPSS.TA.2.1.c3-00025-8976_GEN_PACK-1.80110.1.99393.1
Date: May 31 2017 06:30:21, May 17 2017 02:00:00, 8952.gen
Software [color=#1b8ede]IMEI[/color]: 35818**********
Removing firmware protection……Done
PLEASE RESTART PHONE MANUALLY!
Read the [color=#1b8ede]manual[/color] at the [color=#1b8ede]official site[/color] www.sigmakey.com for details.
——— 2017-11-28 15:58:28 ———
SigmaKey 2.26.16 ADB: Remove FRP
* daemon not running. starting it now *
* daemon started successfully *
Mot Composite ADB Interface
Phone model: motorola Moto G (4)
Android 7.0; Firmware: NPJS25.93-14-10; Date: Mon Aug 28 09:20:48 CDT 2017
Version: NPJS25.93-14-10
[color=#1b8ede]Baseband[/color] Firmware: M8952_70030.25.03.62.01R ATHENE_INDIA_DSDS_CUST
Removing FRP lock….Done

Here is a Screenshot:

Steps to bypass Moto XT1643 Moto G4 Plus FRP:

STEP 1 (Connect):​

• Open “Android ADB” platform in the tab menu in the upper left side of the software
• Open “Qualcomm” bookmark
• Set the phone to the FACTORY MODE: Turn the phone OFF
  Press Vol -, Vol+, Power ON simultaneously, then release Power ON button
• Select FACTORY MODE in the appeared menu, then confirm your selection
• Wait for the phone to fully power ON
• Connect the phone to PC using USB cable
• Install required USB Driver (only if phone is connected for the first time)
• Press “Connect Motorola Android phone”
• Wait for the operation to complete and disconnect the phone

STEP 2 (Reset FRP):​

• Set the phone to the FACTORY MODE:
• Turn the phone OFF
• Press Vol -, Vol+, Power ON simultaneously, then release Power ON button
• Select FACTORY MODE in the appeared menu, then confirm your selection
• Wait for the phone to fully power ON and connect it to PC
• Select “Adb interface” in the port selection tab
• Press “Remove FRP” button
• Message “Done” indicates that the procedure has been completed successfully
• Restart the phone
• We recommend performing master reset from the phone’s menu after completing the remove FRP operation.